Whynotwin11

How to fix a TPM 2.0 failure (enable fTPM or Intel PTT)

Most PCs that fail the TPM check have a firmware TPM that is switched off. Here is how to confirm it, enable it in UEFI setup and re-check.

  • Updated
  • Checked against WhyNotWin11 2.7.0.0
Feature image for the guide: How to fix a TPM 2.0 failure (enable fTPM or Intel PTT)

The TPM Version line is one of the most common red results in WhyNotWin11, and also one of the most fixable. Windows 11 requires Trusted Platform Module (TPM) version 2.0. Many PCs that fail this check actually have a TPM 2.0 built into the processor — it is simply switched off in the firmware settings.

This guide explains what a TPM is, how to confirm what your PC has, how to enable a firmware TPM on Intel and AMD systems, what to do about TPM 1.2, and how to avoid the few real risks involved, such as BitLocker recovery prompts.

What a TPM is and why Windows 11 needs it

A Trusted Platform Module is a small security processor that stores cryptographic keys and measures the start-up process. Windows uses it for features such as:

  • BitLocker and Device Encryption — the TPM protects the key that unlocks the drive.
  • Windows Hello — PINs and biometric credentials are protected by the TPM.
  • Measured and secure start-up — the TPM records what loaded during boot, so tampering can be detected.
  • Credential protection — keys stay inside the chip rather than in normal memory.

Microsoft made TPM 2.0 a minimum requirement for Windows 11 so these protections can be relied on across all supported PCs.

Discrete TPM and firmware TPM

There are two kinds of TPM:

TypeWhat it isCommon in
Discrete TPM (dTPM)A separate chip on the motherboard or a plug-in moduleBusiness laptops and desktops, some enthusiast boards
Firmware TPM (fTPM)TPM functions running inside the processor's security subsystemMost consumer PCs with modern Intel and AMD processors

Intel calls its firmware TPM Platform Trust Technology (PTT). AMD calls it fTPM. Both provide TPM 2.0 and satisfy the Windows 11 requirement.

Step 1: Confirm what Windows sees

Before changing anything, find out exactly what is wrong.

Use the TPM management console

  1. Press Win + R.
  2. Type tpm.msc and press Enter.
  3. Read the result.
What you seeMeaning
"Compatible TPM cannot be found"No TPM is enabled, or the firmware hides it
Status "The TPM is ready for use" and Specification Version 2.0The TPM is fine
Specification Version 1.2An older TPM that does not meet the requirement
TPM present but not readyIt exists but needs to be prepared by Windows

Use PowerShell

Open PowerShell as administrator and run:

TPM status · PowerShell
Get-Tpm

The output lists fields such as TpmPresent, TpmReady, TpmEnabled and TpmActivated. If TpmPresent is False, Windows cannot see a TPM at all, which usually means the firmware option is disabled.

Check the firmware mode too

Press Win + R, type msinfo32 and look at BIOS Mode. A firmware TPM works in both modes on many boards, but Windows 11 also needs UEFI boot. If you see "Legacy", plan to convert the disk to GPT and switch to UEFI as part of the same session.

Step 2: Prepare before changing firmware settings

Find your BitLocker recovery key

  • Open Settings and search for Device encryption or BitLocker.
  • If you sign in with a Microsoft account, the key is usually stored in that account's device list.
  • Write it down or print it. Do not keep the only copy on the drive it protects.

Suspend BitLocker

From an administrator Command Prompt:

Suspend BitLocker · Command Prompt
manage-bde -protectors -disable C: -RebootCount 2

This suspends protection for the next two restarts and resumes it automatically afterwards.

Step 3: Open the UEFI firmware settings

From Windows

  1. Open Settings.
  2. Windows 10: go to Update & Security, then Recovery. Windows 11: go to System, then Recovery.
  3. Under Advanced startup, select Restart now.
  4. Choose Troubleshoot, then Advanced options, then UEFI Firmware Settings, and select Restart.

With a key at start-up

If the UEFI Firmware Settings option is missing, the PC is booting in Legacy mode. Restart and press the setup key shown on the screen. Common keys are Del, F2, F10, F1 and Esc, depending on the manufacturer.

Step 4: Enable the firmware TPM

Menu names vary between manufacturers. Look in the Security, Advanced or Trusted Computing sections.

Intel systems

Look for one of these names:

  • Intel Platform Trust Technology
  • Intel PTT
  • PTT
  • Firmware TPM

On some boards the option sits under Advanced → PCH-FW Configuration. Set it to Enabled.

AMD systems

Look for one of these names:

  • AMD fTPM
  • AMD CPU fTPM
  • fTPM switch
  • Firmware TPM

On some boards it sits under Advanced → AMD fTPM configuration. Set it to AMD CPU fTPM or Enabled.

Business PCs from major brands

Laptops and desktops from large manufacturers often use a discrete TPM with an option called Security Chip, TPM Device, TPM State or Security Device Support. Make sure it is Enabled or Available, and that the TPM is not hidden.

Boards with both options

Some motherboards have a header for a plug-in TPM module as well as a firmware TPM. A setting called TPM Device Selection chooses between them. Select Firmware TPM if no module is installed.

Save and restart

Press the save key (often F10), confirm, and let the PC restart into Windows.

Step 5: Check the result

  1. Open tpm.msc again. It should show the TPM is ready for use with Specification Version 2.0.
  2. Run WhyNotWin11 again as administrator. The TPM Version line should show TPM 2 detected and turn green.
  3. If you suspended BitLocker, it resumes automatically after the restart count you set, or you can resume it from the BitLocker control panel.

What to do if you only have TPM 1.2

Some business PCs from around 2015 and 2016 shipped with a discrete TPM running version 1.2 firmware. Certain manufacturers released tools that update those chips to TPM 2.0.

Look for a manufacturer update

  1. Note your exact model number from the label or from msinfo32.
  2. Visit the manufacturer's support page for that model.
  3. Look for a TPM firmware update to version 2.0 in the BIOS or firmware category.
  4. Read the instructions carefully. TPM updates often require clearing the TPM, which removes keys stored in it.

If no update exists

A TPM 1.2-only PC cannot meet the Windows 11 requirement through settings. The options are the same as for an unsupported processor: stay on Windows 10 with Extended Security Updates, replace the PC, or accept the risks of an unsupported installation.

Common problems and their fixes

ProblemLikely causeFix
No TPM option in the firmwareOld firmware or a model without a TPMUpdate the BIOS from the manufacturer, then look again
TPM enabled but still not detectedTPM hidden or set to discrete without a moduleCheck TPM Device Selection and visibility settings
BitLocker recovery screen after the changeProtection was not suspendedEnter the recovery key; suspend before future changes
WhyNotWin11 shows a question mark for TPMProgram ran without administrator rightsRun again and choose Yes at the UAC prompt
TPM works but CPU still failsThe processor is not on Microsoft's listTPM is fixed; CPU is a separate hardware limit

A note on clearing the TPM

The TPM management console offers a Clear TPM option. Do not use it to "fix" detection problems. Clearing removes all keys stored in the TPM, which can lock you out of encrypted data and Windows Hello sign-ins. Only clear the TPM when a manufacturer's instructions require it and you have your recovery keys.

A note on older AMD fTPM performance reports

In 2022 AMD acknowledged that some Ryzen systems with fTPM enabled could suffer intermittent stutters, and it addressed the issue in later firmware updates. If you enable fTPM on an AMD board, install the latest BIOS from the motherboard maker first.

How Windows uses the TPM after the upgrade

Once the TPM is enabled and Windows 11 is installed, several features begin to use it automatically or when you turn them on.

Device encryption and BitLocker

On many PCs, signing in with a Microsoft account turns on Device Encryption. The TPM protects the encryption key and releases it only when the start-up process looks normal. Always keep a copy of your recovery key somewhere other than the encrypted PC.

Windows Hello

PINs, fingerprint and face sign-in are tied to keys protected by the TPM. A Windows Hello PIN is linked to the device, which is why it is more secure than a password that can be reused elsewhere.

Security features that rely on trusted start-up

Windows security features use the TPM's measurements of the start-up process to detect tampering. Keeping the TPM enabled, together with Secure Boot, gives these features a reliable foundation.

A quick pre-change checklist

  • Files backed up.
  • BitLocker or Device Encryption recovery key saved somewhere safe.
  • BitLocker protection suspended for the next restarts.
  • Latest BIOS or firmware installed from the PC or motherboard maker.
  • Exact model number noted, in case you need the manufacturer's documentation.
  • You know which setting you are looking for: Intel PTT, AMD fTPM or Security Chip.

Summary

Check tpm.msc or Get-Tpm, save your BitLocker key, enable Intel PTT or AMD fTPM in the firmware, and confirm the change in Windows and in WhyNotWin11. If the PC only has TPM 1.2, look for a manufacturer update; without one, the requirement cannot be met in software. Never clear the TPM unless instructions require it and your recovery keys are safe.

Frequently asked questions

Will enabling the TPM delete my files?

No. Enabling a firmware TPM does not touch your disk. Clearing an existing TPM can remove keys, which is why you should never clear it without a reason.

Is a firmware TPM as good as a discrete chip for Windows 11?

For the Windows 11 requirement, yes. Both are TPM 2.0 and both are accepted.

My PC is from 2016. Does it have a TPM?

Many PCs from that period have either a firmware TPM or a discrete TPM 1.2. Check tpm.msc and the firmware settings. Note that many processors from that period are also not on Microsoft's supported list, which is a separate requirement.

Do I need to enable Secure Boot at the same time?

They are separate requirements, but they are often fixed in the same firmware session. Secure Boot needs UEFI mode, so complete any MBR to GPT conversion first.

WhyNotWin11 now shows TPM 2 detected. Is the PC ready?

Only if every other line is green too. Run the full check and read all eleven results.

Can a virtual machine have a TPM?

Yes. Hyper-V Generation 2 virtual machines and other virtualisation products can provide a virtual TPM. Inside a virtual machine, WhyNotWin11 reports the virtual TPM, not your physical one.

My firmware has both "TPM" and "PTT" options. Which one do I need?

If no separate TPM module is fitted, choose PTT (Intel) or fTPM (AMD). The option for a discrete TPM only works when the module is installed.

Does enabling the TPM affect gaming or performance?

For almost all users there is no noticeable effect. Keep the firmware up to date, because manufacturers have fixed rare performance issues in the past.

Will Windows 11 refuse to start if I later disable the TPM?

Windows will usually still start, but features such as BitLocker and Windows Hello depend on it, and BitLocker may ask for its recovery key. Leave the TPM enabled after upgrading.

Is a plug-in TPM module a good idea?

On desktop boards that have a TPM header but no usable firmware TPM, a module that matches the board's header can add TPM 2.0. Buy the module the motherboard maker lists for your exact board.

How do I know whether my PC uses a firmware TPM or a chip?

In tpm.msc, the manufacturer information under TPM Manufacturer Information often names the processor maker for a firmware TPM, such as Intel or AMD, or a chip maker for a discrete TPM. The firmware setting name — PTT, fTPM or Security Chip — is another clue.